- Hardware Manuals
- Commissioning and Tuning Guide
- Software Reference
- Resources
The Industrial I/O Cable Adapter is a compact module converting LVTTL (3.3 V) logic level IOs into standard industrial isolated 24 V I/Os. It converts 4 GPIOs to two digital inputs and outputs. The main purpose of the adapter is to enable connection of 24 V I/O industrial devices to SOMANET servo drives.
Attention
The numbers indicated in the block diagram don’t necessarily need to coincide with the Digital I/O ports of the drive. Especially when SOMANET Circulo is used, it is important to consider that port 4 is Digital Output only!
General Specifications |
|
---|---|
Nominal operating voltage |
24 V DC (-15 %/+20 %) |
Electrical isolation |
500 V (field potential) |
Conductor types |
solid wire, stranded wire and ferrule |
Weight |
< 10g |
Dimensions (LxWxH) |
32mm (47mm 1) x 18mm x 12mm |
Operating temperature |
-25…+60 °C |
Storage temperature |
-40…+85 °C |
Digital Inputs 24V |
|
Number of inputs |
2 |
“0” input signal voltage |
-3…+5 V (Type 1/3 according to EN 61131-2) |
“1” input signal voltage |
11…30 V (Type 3 according to EN 61131-2) |
Input current |
typ. 3 mA (Type 3 according to EN 61131-2) |
Digital Outputs 24V |
|
Number of outputs |
2 |
Output load type |
ohmic, inductive, lamp load |
Output current |
0.35 A (short-circuit-proof) per channel |
Output short circuit current |
typ. < 1 A |
With attached strain relief.
J1 Conector |
|
---|---|
Manufacturer |
JST |
Part number |
SM08B-GHS-TB(LF)(SN) |
Conductor cross section AWG min. |
30 |
Conductor cross section AWG max. |
26 |
Mating part for Housing |
GHR-08V-S |
Crimping Contact |
SSHL-002T-P0.2 |
J2 and J3 Connectors |
|
---|---|
Manufacturer |
Phoenix Contact |
Part number |
1771059 |
Conductor cross section solid min. |
0.14 mm² |
Conductor cross section solid max. |
0.5 mm² |
Conductor cross section flexible min. |
0.2 mm² |
Conductor cross section flexible max. |
0.5 mm² |
Conductor cross section flexible, with ferrule without plastic sleeve min. |
0.25 mm² |
Conductor cross section flexible, with ferrule without plastic sleeve max. |
0.5 mm² |
Conductor cross section AWG min. |
26 |
Conductor cross section AWG max. |
20 |
Note
No mating part required. This push-IN terminal works with solid and flexible cables as well as ferrules.
Note
The PCB can be shrinked to a shrink tube with a diameter of 20 mm.
The board will be delivered with a strain relief. A cable tie can be used as a strain reliever:
On the right side of the image, the cable tie is symbolized in red and the cables in black. The Synapticon Logo can be connected to PE, e.g. the shield of a cable. There is the possibility to place a CAP and a resistor between PE and GND. In Standard version this is not placed.
If not needed, the strain reliever part can be broken off, then the module is shorter.
Cables can also directly be soldered to the PCB. If this option is needed, please contact sales@synapticon.com
Due to its small size, the adapter isn’t equipped with a specific hole for screwing it to a structure. If it has been fitted into a shrink tube, it can be treated like a cable. It’s also possible to attach it using a zip tie.